config DM_PMIC bool "Enable Driver Model for PMIC drivers (UCLASS_PMIC)" depends on DM ---help--- This config enables the driver-model PMIC support. UCLASS_PMIC - designed to provide an I/O interface for PMIC devices. For the multi-function PMIC devices, this can be used as parent I/O device for each IC's interface. Then, each children uses its parent for read/write. For detailed description, please refer to the files: - 'drivers/power/pmic/pmic-uclass.c' - 'include/power/pmic.h' if DM_PMIC config SPL_DM_PMIC bool "Enable Driver Model for PMIC drivers (UCLASS_PMIC) in SPL" depends on SPL_DM default y ---help--- This config enables the driver-model PMIC support in SPL. UCLASS_PMIC - designed to provide an I/O interface for PMIC devices. For the multi-function PMIC devices, this can be used as parent I/O device for each IC's interface. Then, each children uses its parent for read/write. For detailed description, please refer to the files: - 'drivers/power/pmic/pmic-uclass.c' - 'include/power/pmic.h' config PMIC_CHILDREN bool "Allow child devices for PMICs" default y ---help--- This allows PMICs to support child devices (such as regulators) in SPL. This adds quite a bit of code so if you are not using this feature you can turn it off. Most likely you should turn it on for U-Boot proper. config SPL_PMIC_CHILDREN bool "Allow child devices for PMICs in SPL" depends on SPL_DM_PMIC default y ---help--- This allows PMICs to support child devices (such as regulators) in SPL. This adds quite a bit of code so if you are not using this feature you can turn it off. In this case you may need a 'back door' to call your regulator code (e.g. see rk8xx.c for direct functions for use in SPL). config PMIC_AB8500 bool "Enable driver for ST-Ericsson AB8500 PMIC via PRCMU" select REGMAP select SYSCON help Enable support for the ST-Ericsson AB8500 (Analog Baseband) PMIC. It connects with the ST-Ericsson DB8500 SoC via an I2C bus managed by the power/reset/clock management unit (PRCMU) firmware. config PMIC_ACT8846 bool "Enable support for the active-semi 8846 PMIC" depends on DM_I2C ---help--- This PMIC includes 4 DC/DC step-down buck regulators and 8 low-dropout regulators (LDOs). It also provides some GPIO, reset and battery functions. It uses an I2C interface and is designed for use with tablets and smartphones. config PMIC_AXP bool "Enable Driver Model for X-Powers AXP PMICs" depends on DM_I2C select SYSRESET_CMD_POWEROFF if SYSRESET && CMD_POWEROFF imply CMD_POWEROFF if SYSRESET help This config enables driver-model PMIC uclass features for X-Powers AXP152, AXP2xx, and AXP8xx PMICs. config SPL_PMIC_AXP bool "Enable Driver Model for X-Powers AXP PMICs in SPL" depends on SPL_DM_I2C && SPL_DM_PMIC help This config enables driver-model PMIC uclass features in the SPL for X-Powers AXP152, AXP2xx, and AXP8xx PMICs. config DM_PMIC_DA9063 bool "Enable Driver Model for the Dialog DA9063 PMIC" help This config enables implementation of driver-model pmic uclass features for PMIC DA9063. The driver implements read/write operations. config SPL_DM_PMIC_DA9063 bool "Enable Driver Model for the Dialog DA9063 PMIC in SPL" depends on SPL_DM_PMIC help This config enables implementation of driver-model pmic uclass features for PMIC DA9063. The driver implements read/write operations. config PMIC_AS3722 bool "Enable support for the Austria Micro Systems (AMS) AS7322 PMIC" help The AS3722 includes 7 DC/DC buck convertors, 11 low-noise LDOs, a real-time clock, GPIOs, ADC and a few other features. It uses an I2C interface and is designs to cover most of the power managementment required for a tablets or laptop. config DM_PMIC_BD71837 bool "Enable Driver Model for PMIC BD71837" help This config enables implementation of driver-model pmic uclass features for PMIC BD71837. The driver implements read/write operations. config SPL_DM_PMIC_BD71837 bool "Enable Driver Model for PMIC BD71837 in SPL stage" depends on SPL_DM_PMIC help This config enables implementation of driver-model pmic uclass features for PMIC BD71837. The driver implements read/write operations. config DM_PMIC_FAN53555 bool "Enable support for OnSemi FAN53555" depends on DM_REGULATOR && DM_I2C select DM_REGULATOR_FAN53555 help This config enables implementation of driver-model PMIC uclass features for the FAN53555 regulator. The FAN53555 is a (family of) single-output regulators that supports transitioning between two different output voltages based on an voltage selection pin. The driver implements read/write operations for use with the FAN53555 regulator driver and binds the regulator driver to its node. config SPL_DM_PMIC_FAN53555 bool "Enable support for OnSemi FAN53555 in SPL" depends on SPL_DM_REGULATOR && SPL_DM_I2C select SPL_DM_REGULATOR_FAN53555 help This config enables implementation of driver-model PMIC uclass features for the FAN53555 regulator. The FAN53555 is a (family of) single-output regulators that supports transitioning between two different output voltages based on an voltage selection pin. The driver implements read/write operations for use with the FAN53555 regulator driver and binds the regulator driver to its node. config DM_PMIC_MP5416 bool "Enable Driver Model for PMIC MP5416" help This config enables implementation of driver-model pmic uclass features for PMIC MP5416. The driver implements read/write operations. config SPL_DM_PMIC_MP5416 bool "Enable Driver Model for PMIC MP5416 in SPL stage" depends on SPL_DM_PMIC help This config enables implementation of driver-model pmic uclass features for PMIC MP5416. The driver implements read/write operations. config DM_PMIC_PCA9450 bool "Enable Driver Model for PMIC PCA9450" depends on DM_I2C help This config enables implementation of driver-model pmic uclass features for PMIC PCA9450. The driver implements read/write operations. config SPL_DM_PMIC_PCA9450 bool "Enable Driver Model for PMIC PCA9450 in SPL" depends on SPL_DM_PMIC depends on SPL_DM_I2C help This config enables implementation of driver-model pmic uclass features for PMIC PCA9450 in SPL. The driver implements read/write operations. config DM_PMIC_PFUZE100 bool "Enable Driver Model for PMIC PFUZE100" ---help--- This config enables implementation of driver-model pmic uclass features for PMIC PFUZE100. The driver implements read/write operations. config SPL_DM_PMIC_PFUZE100 bool "Enable Driver Model for PMIC PFUZE100 in SPL" depends on SPL_DM_PMIC ---help--- This config enables implementation of driver-model pmic uclass features for PMIC PFUZE100 in SPL. The driver implements read/write operations. config DM_PMIC_MAX77686 bool "Enable Driver Model for PMIC MAX77686" ---help--- This config enables implementation of driver-model pmic uclass features for PMIC MAX77686. The driver implements read/write operations. config DM_PMIC_MAX8998 bool "Enable Driver Model for PMIC MAX8998" ---help--- This config enables implementation of driver-model pmic uclass features for PMIC MAX8998. The driver implements read/write operations. config DM_PMIC_MC34708 bool "Enable Driver Model for PMIC MC34708" help This config enables implementation of driver-model pmic uclass features for PMIC MC34708. The driver implements read/write operations. config PMIC_MAX8997 bool "Enable Driver Model for PMIC MAX8997" ---help--- This config enables implementation of driver-model pmic uclass features for PMIC MAX8997. The driver implements read/write operations. This is a Power Management IC with RTC, Fuel Gauge, MUIC control on Chip. - 21x LDOs - 12x GPIOs - Haptic Motor driver - RTC with two alarms - Fueal Gauge and One backup battery charger - MUIC - Others config PMIC_QCOM bool "Enable Driver Model for Qualcomm generic PMIC" ---help--- The Qcom PMIC is connected to one (or several) processors with SPMI bus. It has 2 slaves with several peripherals: - 18x LDO - 4x GPIO - Power and Reset buttons - Watchdog - RTC - Vibrator drivers - Others Driver binding info: doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt config PMIC_RK8XX bool "Enable support for Rockchip PMIC RK8XX" select SYSRESET_CMD_POWEROFF if SYSRESET && CMD_POWEROFF ---help--- The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8 LDOs, an RTC and two low Rds (resistance (drain to source)) switches. It is accessed via an I2C interface. The device is used with Rockchip SoCs. This driver implements register read/write operations. config SPL_PMIC_RK8XX bool "Enable support for Rockchip PMIC RK8XX" depends on SPL_DM_PMIC ---help--- The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8 LDOs, an RTC and two low Rds (resistance (drain to source)) switches. It is accessed via an I2C interface. The device is used with Rockchip SoCs. This driver implements register read/write operations. config PMIC_S2MPS11 bool "Enable Driver Model for PMIC Samsung S2MPS11" ---help--- The Samsung S2MPS11 PMIC provides: - 38 adjustable LDO regulators - 9 High-Efficiency Buck Converters - 1 BuckBoost Converter - RTC with two alarms - Backup battery charger - I2C Configuration Interface This driver provides access to I/O interface only. Binding info: doc/device-tree-bindings/pmic/s2mps11.txt config DM_PMIC_SANDBOX bool "Enable Driver Model for emulated Sandbox PMIC" ---help--- Enable the driver for Sandbox PMIC emulation. The emulated PMIC device depends on two drivers: - sandbox PMIC I/O driver - implements dm pmic operations - sandbox PMIC i2c emul driver - emulates the PMIC's I2C transmission A detailed information can be found in header: '' The Sandbox PMIC info: * I/O interface: - I2C chip address: 0x40 - first register address: 0x0 - register count: 0x10 * Adjustable outputs: - 2x LDO - 2x BUCK - Each, with a different operating conditions (header). * Reset values: - set by i2c emul driver's probe() (defaults in header) Driver binding info: doc/device-tree-bindings/pmic/sandbox.txt config PMIC_S5M8767 bool "Enable Driver Model for the Samsung S5M8767 PMIC" ---help--- The S5M8767 PMIC provides a large array of LDOs and BUCKs for use as a SoC power controller. It also provides 32KHz clock outputs. This driver provides basic register access and sets up the attached regulators if regulator support is enabled. config PMIC_RN5T567 bool "Enable driver for Ricoh RN5T567 PMIC" ---help--- The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO regulators Real-Time Clock and 4 GPIOs. This driver provides register access only. config SPL_PMIC_RN5T567 bool "Enable driver for Ricoh RN5T567 PMIC in SPL" depends on SPL_DM_PMIC ---help--- The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO regulators Real-Time Clock and 4 GPIOs. This driver provides register access only. config PMIC_TPS65090 bool "Enable driver for Texas Instruments TPS65090 PMIC" ---help--- The TPS65090 is a PMIC containing several LDOs, DC to DC convertors, FETs and a battery charger. This driver provides register access only, and you can enable the regulator/charger drivers separately if required. config PMIC_PALMAS bool "Enable driver for Texas Instruments PALMAS PMIC" ---help--- The PALMAS is a PMIC containing several LDOs, SMPS. This driver binds the pmic children. config PMIC_LP873X bool "Enable driver for Texas Instruments LP873X PMIC" ---help--- The LP873X is a PMIC containing couple of LDOs and couple of SMPS. This driver binds the pmic children. config PMIC_LP87565 bool "Enable driver for Texas Instruments LP87565 PMIC" ---help--- The LP87565 is a PMIC containing a bunch of SMPS. This driver binds the pmic children. config DM_PMIC_TPS65910 bool "Enable driver for Texas Instruments TPS65910 PMIC" ---help--- The TPS65910 is a PMIC containing 3 buck DC-DC converters, one boost DC-DC converter, 8 LDOs and a RTC. This driver binds the SMPS and LDO pmic children. config PMIC_STPMIC1 bool "Enable support for STMicroelectronics STPMIC1 PMIC" depends on DM_I2C select SYSRESET_CMD_POWEROFF if CMD_POWEROFF && !ARM_PSCI_FW ---help--- The STPMIC1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power switches. It is accessed via an I2C interface. The device is used with STM32MP1 SoCs. This driver implements register read/write operations. config SPL_PMIC_PALMAS bool "Enable driver for Texas Instruments PALMAS PMIC" depends on SPL_DM_PMIC help The PALMAS is a PMIC containing several LDOs, SMPS. This driver binds the pmic children in SPL. config SPL_PMIC_LP873X bool "Enable driver for Texas Instruments LP873X PMIC" depends on SPL_DM_PMIC help The LP873X is a PMIC containing couple of LDOs and couple of SMPS. This driver binds the pmic children in SPL. config SPL_PMIC_LP87565 bool "Enable driver for Texas Instruments LP87565 PMIC" depends on SPL_DM_PMIC help The LP87565 is a PMIC containing a bunch of SMPS. This driver binds the pmic children in SPL. config PMIC_TPS65941 bool "Enable driver for Texas Instruments TPS65941 PMIC" help The TPS65941 is a PMIC containing a bunch of SMPS & LDOs. This driver binds the pmic children. config PMIC_TPS65219 bool "Enable driver for Texas Instruments TPS65219 PMIC" depends on DM_PMIC help The TPS65219 is a PMIC containing a bunch of SMPS & LDOs. This driver binds the pmic children. endif config PMIC_TPS65217 bool "Enable driver for Texas Instruments TPS65217 PMIC" ---help--- The TPS65217 is a PMIC containing several LDOs, DC to DC convertors, FETs and a battery charger. This driver provides register access only, and you can enable the regulator/charger drivers separately if required. config POWER_TPS65218 bool "Enable legacy driver for TPS65218 PMIC" config POWER_TPS62362 bool "Enable legacy driver for TPS62362 PMIC" config SPL_POWER_TPS62362 bool "Enable legacy driver for TPS62362 PMIC in SPL" default y if POWER_TPS62362 depends on SPL config SPL_POWER_TPS65910 bool "Enable legacy driver for TPS65910 PMIC in SPL" depends on SPL if POWER_LEGACY || SPL_POWER_LEGACY config POWER_HI6553 bool "Enable legacy driver for HI6553 PMIC" config POWER_LTC3676 bool "Enable legacy driver for LTC3676 PMIC" config POWER_PCA9450 bool "Enable legacy driver for PCA9450 PMIC" config POWER_PFUZE100 bool "Enable legacy driver for PFUZE100 PMIC" config POWER_PFUZE3000 bool "Enable legacy driver for PFUZE3000 PMIC" config POWER_MC34VR500 bool "Enable driver for Freescale MC34VR500 PMIC" ---help--- The MC34VR500 is used in conjunction with the FSL T1 and LS1 series SoC. It provides 4 buck DC-DC convertors and 5 LDOs, and it is accessed via an I2C interface. endif