// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2016 NXP Semiconductors * Author: Fabio Estevam */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "../freescale/common/pfuze.h" #include #include DECLARE_GLOBAL_DATA_PTR; int dram_init(void) { gd->ram_size = PHYS_SDRAM_SIZE; /* Subtract the defined OPTEE runtime firmware length */ #ifdef CONFIG_OPTEE_TZDRAM_SIZE gd->ram_size -= CONFIG_OPTEE_TZDRAM_SIZE; #endif return 0; } static iomux_v3_cfg_t const wdog_pads[] = { MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL), }; #ifdef CONFIG_DM_PMIC int power_init_board(void) { struct udevice *dev; int ret, dev_id, rev_id; ret = pmic_get("pfuze3000@8", &dev); if (ret == -ENODEV) return 0; if (ret != 0) return ret; dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID); rev_id = pmic_reg_read(dev, PFUZE3000_REVID); printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id); /* disable Low Power Mode during standby mode */ pmic_reg_write(dev, PFUZE3000_LDOGCTL, 1); return 0; } #endif int board_init(void) { /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; return 0; } int checkboard(void) { char *mode; if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT)) mode = "secure"; else mode = "non-secure"; #ifdef CONFIG_OPTEE_TZDRAM_SIZE unsigned long optee_start, optee_end; optee_end = PHYS_SDRAM + PHYS_SDRAM_SIZE; optee_start = optee_end - CONFIG_OPTEE_TZDRAM_SIZE; printf("Board: WARP7 in %s mode OPTEE DRAM 0x%08lx-0x%08lx\n", mode, optee_start, optee_end); #else printf("Board: WARP7 in %s mode\n", mode); #endif return 0; } int board_late_init(void) { struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR; #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG struct tag_serialnr serialnr; char serial_string[0x20]; #endif imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads)); set_wdog_reset(wdog); /* * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4), * since we use PMIC_PWRON to reset the board. */ clrsetbits_le16(&wdog->wcr, 0, 0x10); #ifdef CONFIG_IMX_HAB /* Determine HAB state */ env_set_ulong(HAB_ENABLED_ENVNAME, imx_hab_is_enabled()); #else env_set_ulong(HAB_ENABLED_ENVNAME, 0); #endif #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG /* Set serial# standard environment variable based on OTP settings */ get_board_serial(&serialnr); snprintf(serial_string, sizeof(serial_string), "WaRP7-0x%08x%08x", serialnr.low, serialnr.high); env_set("serial#", serial_string); #endif return 0; }