// SPDX-License-Identifier: GPL-2.0+ /* * am3517evm.c - board file for TI's AM3517 family of devices. * * Author: Vaibhav Hiremath * * Based on ti/evm/evm.c * * Copyright (C) 2010 * Texas Instruments Incorporated - http://www.ti.com/ */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "am3517evm.h" DECLARE_GLOBAL_DATA_PTR; #define AM3517_IP_SW_RESET 0x48002598 #define CPGMACSS_SW_RST (1 << 1) #define PHY_GPIO 30 #if defined(CONFIG_SPL_BUILD) #if defined(CONFIG_SPL_OS_BOOT) int spl_start_uboot(void) { /* break into full u-boot on 'c' */ return serial_tstc() && serial_getc() == 'c'; } #endif #endif /* * Routine: board_init * Description: Early hardware init. */ int board_init(void) { gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ /* board id for Linux */ gd->bd->bi_arch_number = MACH_TYPE_OMAP3517EVM; /* boot param addr */ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); return 0; } #ifdef CONFIG_USB_MUSB_AM35X static struct musb_hdrc_config musb_config = { .multipoint = 1, .dyn_fifo = 1, .num_eps = 16, .ram_bits = 12, }; static struct omap_musb_board_data musb_board_data = { .set_phy_power = am35x_musb_phy_power, .clear_irq = am35x_musb_clear_irq, .reset = am35x_musb_reset, }; static struct musb_hdrc_platform_data musb_plat = { #if defined(CONFIG_USB_MUSB_HOST) .mode = MUSB_HOST, #elif defined(CONFIG_USB_MUSB_GADGET) .mode = MUSB_PERIPHERAL, #else #error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" #endif .config = &musb_config, .power = 250, .platform_ops = &am35x_ops, .board_data = &musb_board_data, }; static void am3517_evm_musb_init(void) { /* * Set up USB clock/mode in the DEVCONF2 register. * USB2.0 PHY reference clock is 13 MHz */ clrsetbits_le32(&am35x_scm_general_regs->devconf2, CONF2_REFFREQ | CONF2_OTGMODE | CONF2_PHY_GPIOMODE, CONF2_REFFREQ_13MHZ | CONF2_SESENDEN | CONF2_VBDTCTEN | CONF2_DATPOL); musb_register(&musb_plat, &musb_board_data, (void *)AM35XX_IPSS_USBOTGSS_BASE); } #else #define am3517_evm_musb_init() do {} while (0) #endif /* * Routine: misc_init_r * Description: Init i2c, ethernet, etc... (done here so udelay works) */ int misc_init_r(void) { omap_die_id_display(); am3517_evm_musb_init(); return 0; } /* * Routine: set_muxconf_regs * Description: Setting up the configuration Mux registers specific to the * hardware. Many pins need to be moved from protect to primary * mode. */ void set_muxconf_regs(void) { MUX_AM3517EVM(); } #if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) int board_eth_init(struct bd_info *bis) { int rv, n = 0; rv = cpu_eth_init(bis); if (rv > 0) n += rv; rv = usb_eth_initialize(bis); if (rv > 0) n += rv; return n; } #endif