# SPDX-License-Identifier: GPL-2.0+ # # Copyright (C) 2019, Pascal Linder config VENDOR_KM bool help Selected by any KM board to have additional configurations. if VENDOR_KM menu "KM Board Setup" config SYS_I2C_INIT_BOARD def_bool y if ARM config HUSH_INIT_VAR def_bool y config KM_PNVRAM hex "Pseudo RAM" default 0x80000 depends on !ARCH_SOCFPGA help Start address of the pseudo non-volatile RAM for application. config KM_PHRAM hex "Physical RAM" default 0x17F000 if ARM && !ARCH_LS1021A default 0x100000 if PPC || ARCH_LS1021A depends on !ARCH_SOCFPGA help Start address of the physical RAM, which is the mounted /var folder. config KM_RESERVED_PRAM hex "Reserved RAM" default 0x0 if MPC83xx default 0x1000 if MPC85xx || ARCH_LS1021A depends on !ARCH_SOCFPGA help Reserved physical RAM area at the end of memory for special purposes. config KM_CRAMFS_ADDR hex "CRAMFS Address" default 0x83000000 if ARCH_LS1021A default 0x3000000 depends on !ARCH_SOCFPGA help Start address of the CRAMFS containing the Linux kernel. config KM_KERNEL_ADDR hex "Kernel Load Address" default 0x82000000 if ARCH_LS1021A default 0x2000000 help Address where to load Linux kernel in RAM. config KM_FDT_ADDR hex "FDT Load Address" default 0x82FC0000 if ARCH_LS1021A default 0x2FC0000 help Address where to load flattened device tree in RAM. config SYS_PAX_BASE hex "PAX IFC Base Address" default 0x78000000 depends on ARCH_LS1021A help IFC Base Address for PAXx FPGA. config SYS_CLIPS_BASE hex "CLIPS IFC Base Address" default 0x78000000 depends on ARCH_LS1021A help IFC Base Address for CLIPS FPGA. config KM_COMMON_ETH_INIT bool "Common Ethernet Initialization" default y if MPC83xx default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A help Use the Ethernet initialization implemented in common code that detects if a Piggy board is present. config PIGGY_MAC_ADDRESS_OFFSET int "Piggy Address Offset" default 0 help MAC address offset for the Piggy board. config KM_MVEXTSW_ADDR hex "Marvell Switch Address" depends on MV88E6352_SWITCH default 0x10 help Address of external Marvell switch. config KM_IVM_BUS int "IVM I2C Bus" default 0 if ARCH_SOCFPGA default 1 if PPC || ARCH_LS1021A help Identifier number of I2C bus, where the inventory EEPROM is connected to. config SYS_IVM_EEPROM_ADR hex "IVM I2C Address" default 0x50 help I2C address of the EEPROM containing the inventory. config SYS_IVM_EEPROM_MAX_LEN hex "IVM Length" default 0x400 help Maximum length of inventory in EEPROM. config SYS_IVM_EEPROM_PAGE_LEN hex "IVM Page Size" default 0x100 help Page size of inventory in EEPROM. config PG_WCOM_UBOOT_UPDATE_SUPPORTED bool "Enable U-Boot Field Fail-Safe Update Functionality" select EVENT default n help Indicates that field fail-safe u-boot update is supported. This functionality works only for designs that are booting from parallel NOR flash. config PG_WCOM_UBOOT_BOOTPACKAGE bool "U-Boot Is Part Of Factory Boot-Package Image" default n help Indicates that u-boot will be a part of the factory programmed boot-package image. Has to be set for original u-boot programmed at factory. config PG_WCOM_UBOOT_UPDATE_TEXT_BASE hex "Text Base For U-Boot Programmed Outside Factory" default 0xFFFFFFFF help Text base of an updated u-boot that is not factory programmed but later when the unit is rolled out on the field. Has to be set for original u-boot programmed at factory. config PG_WCOM_UBOOT_UPDATE bool "U-Boot Is Part Of Factory Boot-Package Image" default n help Indicates that u-boot will be a part of the embedded software and programmed at field. Has to be set for updated u-boot version programmed at field. source "board/keymile/km83xx/Kconfig" source "board/keymile/kmcent2/Kconfig" source "board/keymile/pg-wcom-ls102xa/Kconfig" endmenu endif