/* SPDX-License-Identifier: GPL-2.0+ */ /* * (C) Copyright 2007 Michal Simek * (C) Copyright 2004 Atmark Techno, Inc. * * Michal SIMEK * Yasushi SHOJI */ #include #include #define SYM_ADDR(reg, reg_add, symbol) \ mfs r20, rpc; \ addik r20, r20, _GLOBAL_OFFSET_TABLE_ + 8; \ lwi reg, r20, symbol@GOT; \ addk reg, reg reg_add; .text .global _start _start: mts rmsr, r0 /* disable cache */ mfs r20, rpc addi r20, r20, -4 mts rslr, r0 mts rshr, r20 #if defined(CONFIG_SPL_BUILD) addi r1, r0, CONFIG_SPL_STACK #else add r1, r0, r20 bri 1f /* Force alignment for easier ASM code below */ #define ALIGNMENT_ADDR 0x20 .align 4 uboot_dyn_start: .word __rel_dyn_start uboot_dyn_end: .word __rel_dyn_end uboot_sym_start: .word __dyn_sym_start 1: addi r5, r20, 0 add r6, r0, r0 lwi r7, r20, ALIGNMENT_ADDR addi r7, r7, -CONFIG_TEXT_BASE add r7, r7, r5 lwi r8, r20, ALIGNMENT_ADDR + 0x4 addi r8, r8, -CONFIG_TEXT_BASE add r8, r8, r5 lwi r9, r20, ALIGNMENT_ADDR + 0x8 addi r9, r9, -CONFIG_TEXT_BASE add r9, r9, r5 addi r10, r0, CONFIG_TEXT_BASE brlid r15, mb_fix_rela nop #endif addi r1, r1, -4 /* Decrement SP to top of memory */ /* Call board_init_f_alloc_reserve with the current stack pointer as * parameter. */ add r5, r0, r1 brlid r15, board_init_f_alloc_reserve nop /* board_init_f_alloc_reserve returns a pointer to the allocated area * in r3. Set the new stack pointer below this area. */ add r1, r0, r3 mts rshr, r1 addi r1, r1, -4 /* Call board_init_f_init_reserve with the address returned by * board_init_f_alloc_reserve as parameter. */ add r5, r0, r3 brlid r15, board_init_f_init_reserve nop #if !defined(CONFIG_SPL_BUILD) /* Setup vectors with pre-relocation symbols */ or r5, r0, r0 brlid r15, __setup_exceptions nop #endif /* * Initialize global data cpuinfo with default values (cache * size, cache line size, etc). */ brlid r15, microblaze_early_cpuinfo_init nop /* Flush cache before enable cache */ brlid r15, flush_cache_all nop /* enable instruction and data cache */ mfs r12, rmsr ori r12, r12, 0x1a0 mts rmsr, r12 clear_bss: /* clear BSS segments */ SYM_ADDR(r5, r0, __bss_start) SYM_ADDR(r4, r0, __bss_end) cmp r6, r5, r4 beqi r6, 3f 2: swi r0, r5, 0 /* write zero to loc */ addi r5, r5, 4 /* increment to next loc */ cmp r6, r5, r4 /* check if we have reach the end */ bnei r6, 2b 3: /* jumping to board_init */ #ifdef CONFIG_DEBUG_UART brlid r15, debug_uart_init nop #endif #ifndef CONFIG_SPL_BUILD or r5, r0, r0 /* flags - empty */ bri board_init_f #else bri board_init_r #endif 1: bri 1b #ifndef CONFIG_SPL_BUILD .text .ent __setup_exceptions .align 2 /* * Set up reset, interrupt, user exception and hardware exception vectors. * * Parameters: * r5 - relocation offset (zero when setting up vectors before * relocation, and gd->reloc_off when setting up vectors after * relocation) * - the relocation offset is added to the _exception_handler, * _interrupt_handler and _hw_exception_handler symbols to reflect the * post-relocation memory addresses * * Reserve registers: * r10: Stores little/big endian offset for vectors * r2: Stores imm opcode * r3: Stores brai opcode * r4: Stores the vector base address */ __setup_exceptions: addik r1, r1, -32 swi r2, r1, 4 swi r3, r1, 8 swi r4, r1, 12 swi r6, r1, 16 swi r7, r1, 20 swi r8, r1, 24 swi r10, r1, 28 /* Find-out if u-boot is running on BIG/LITTLE endian platform * There are some steps which is necessary to keep in mind: * 1. Setup offset value to r6 * 2. Store word offset value to address 0x0 * 3. Load just byte from address 0x0 * 4a) LITTLE endian - r10 contains 0x2 because it is the smallest * value that's why is on address 0x0 * 4b) BIG endian - r10 contains 0x0 because 0x2 offset is on addr 0x3 */ addik r6, r0, 0x2 /* BIG/LITTLE endian offset */ sw r6, r1, r0 lbu r10, r1, r0 /* add opcode instruction for 32bit jump - 2 instruction imm & brai */ addi r2, r0, 0xb0000000 /* hex b000 opcode imm */ addi r3, r0, 0xb8080000 /* hew b808 opcode brai */ /* Store the vector base address in r4 */ addi r4, r0, CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR /* reset address */ swi r2, r4, 0x0 /* reset address - imm opcode */ swi r3, r4, 0x4 /* reset address - brai opcode */ SYM_ADDR(r6, r0, _start) /* Intentionally keep reset vector back to origin u-boot location */ sw r6, r1, r0 lhu r7, r1, r10 rsubi r8, r10, 0x2 sh r7, r4, r8 rsubi r8, r10, 0x6 sh r6, r4, r8 #if CONFIG_IS_ENABLED(XILINX_MICROBLAZE0_USR_EXCEP) /* user_vector_exception */ swi r2, r4, 0x8 /* user vector exception - imm opcode */ swi r3, r4, 0xC /* user vector exception - brai opcode */ SYM_ADDR(r6, r5, _exception_handler) sw r6, r1, r0 /* * BIG ENDIAN memory map for user exception * 0x8: 0xB000XXXX * 0xC: 0xB808XXXX * * then it is necessary to count address for storing the most significant * 16bits from _exception_handler address and copy it to * 0xa address. Big endian use offset in r10=0 that's why is it just * 0xa address. The same is done for the least significant 16 bits * for 0xe address. * * LITTLE ENDIAN memory map for user exception * 0x8: 0xXXXX00B0 * 0xC: 0xXXXX08B8 * * Offset is for little endian setup to 0x2. rsubi instruction decrease * address value to ensure that points to proper place which is * 0x8 for the most significant 16 bits and * 0xC for the least significant 16 bits */ lhu r7, r1, r10 rsubi r8, r10, 0xa sh r7, r4, r8 rsubi r8, r10, 0xe sh r6, r4, r8 #endif /* interrupt_handler */ swi r2, r4, 0x10 /* interrupt - imm opcode */ swi r3, r4, 0x14 /* interrupt - brai opcode */ SYM_ADDR(r6, r5, _interrupt_handler) sw r6, r1, r0 lhu r7, r1, r10 rsubi r8, r10, 0x12 sh r7, r4, r8 rsubi r8, r10, 0x16 sh r6, r4, r8 /* hardware exception */ swi r2, r4, 0x20 /* hardware exception - imm opcode */ swi r3, r4, 0x24 /* hardware exception - brai opcode */ SYM_ADDR(r6, r5, _hw_exception_handler) sw r6, r1, r0 lhu r7, r1, r10 rsubi r8, r10, 0x22 sh r7, r4, r8 rsubi r8, r10, 0x26 sh r6, r4, r8 lwi r10, r1, 28 lwi r8, r1, 24 lwi r7, r1, 20 lwi r6, r1, 16 lwi r4, r1, 12 lwi r3, r1, 8 lwi r2, r1, 4 addik r1, r1, 32 rtsd r15, 8 or r0, r0, r0 .end __setup_exceptions /* * Relocate u-boot */ .text .global relocate_code .ent relocate_code .align 2 relocate_code: /* * r5 - start_addr_sp * r6 - new_gd * r7 - reloc_addr */ addi r1, r5, 0 /* Start to use new SP */ mts rshr, r1 addi r31, r6, 0 /* Start to use new GD */ /* Relocate text and data - r12 temp value */ SYM_ADDR(r21, r0, _start) SYM_ADDR(r22, r0, _end) /* Include BSS too */ addi r22, r22, -4 rsub r6, r21, r22 or r5, r0, r0 1: lw r12, r21, r5 /* Load u-boot data */ sw r12, r7, r5 /* Write zero to loc */ cmp r12, r5, r6 /* Check if we have reach the end */ bneid r12, 1b addi r5, r5, 4 /* Increment to next loc - relocate code */ /* R23 points to the base address. */ rsub r23, r21, r7 /* keep - this is already here gd->reloc_off */ /* Setup vectors with post-relocation symbols */ add r5, r0, r23 /* load gd->reloc_off to r5 */ brlid r15, __setup_exceptions nop /* reloc_offset is current location */ SYM_ADDR(r10, r0, _start) /* r5 new address where I should copy code */ add r5, r0, r7 /* Move reloc addr to r5 */ /* Verbose message */ addi r6, r0, 0 SYM_ADDR(r7, r0, __rel_dyn_start) rsub r7, r10, r7 add r7, r7, r5 SYM_ADDR(r8, r0, __rel_dyn_end) rsub r8, r10, r8 add r8, r8, r5 SYM_ADDR(r9, r0, __dyn_sym_start) rsub r9, r10, r9 add r9, r9, r5 brlid r15, mb_fix_rela nop /* end of code which does relocation */ /* Flush caches to ensure consistency */ brlid r15, flush_cache_all nop 2: addi r5, r31, 0 /* gd is initialized in board_r.c */ SYM_ADDR(r6, r0, _start) SYM_ADDR(r12, r23, board_init_r) bra r12 /* Jump to relocated code */ .end relocate_code #endif