if ARCH_ZYNQMP config SPL_FS_FAT default y config SPL_LIBCOMMON_SUPPORT default y config SPL_LIBDISK_SUPPORT default y config SPL_LIBGENERIC_SUPPORT default y config SPL_MMC default y if MMC_SDHCI_ZYNQ config SPL_SERIAL default y config SPL_SPI_FLASH_SUPPORT default y if ZYNQ_QSPI config SPL_SPI default y if ZYNQ_QSPI config SYS_BOARD string "Board name" default "zynqmp" config SYS_VENDOR string "Vendor name" default "xilinx" config SYS_SOC default "zynqmp" config SYS_CONFIG_NAME string "Board configuration name" default "xilinx_zynqmp" help This option contains information about board configuration name. Based on this option include/configs/.h header will be used for board configuration. config SYS_MEM_RSVD_FOR_MMU bool "Reserve memory for MMU Table" help If defined this option is used to setup different space for MMU table than the one which will be allocated during relocation. config BOOT_INIT_FILE string "boot.bin init register filename" depends on SPL default "" help Add register writes to boot.bin format (max 256 pairs). Expect a table of register-value pairs, e.g. "0x12345678 0x4321" config PMUFW_INIT_FILE string "PMU firmware" depends on SPL default "" help Include external PMUFW (Platform Management Unit FirmWare) to a Xilinx bootable image (boot.bin). config ZYNQMP_SPL_PM_CFG_OBJ_FILE string "PMU firmware configuration object to load at runtime by SPL" depends on SPL help Path to a binary PMU firmware configuration object to be linked into U-Boot SPL and loaded at runtime into the PMU firmware. The ZynqMP Power Management Unit (PMU) needs a configuration object for most SoC peripherals to work. To have it loaded by U-Boot SPL set here the file name (absolute path or relative to the top source tree) of your configuration, which must be a binary blob. It will be linked in the SPL binary and loaded into the PMU firmware by U-Boot SPL during board initialization. Leave this option empty if your PMU firmware has a hard-coded configuration object or you are loading it by any other means. config ZYNQMP_NO_DDR bool "Disable DDR MMU mapping" help This option configures MMU with no DDR to avoid speculative access to DDR memory where DDR is not present. config SPL_ZYNQMP_DRAM_ECC_INIT bool "Initialize DRAM ECC" depends on SPL help This option initializes all memory to 0xdeadbeef. Must be set if your memory is of ECC type. config SPL_ZYNQMP_DRAM_BANK1_BASE depends on SPL_ZYNQMP_DRAM_ECC_INIT hex "DRAM Bank1 address" default 0x00000000 help Start address of DRAM ECC bank1 config SPL_ZYNQMP_DRAM_BANK1_LEN depends on SPL_ZYNQMP_DRAM_ECC_INIT hex "DRAM Bank1 size" default 0x80000000 help Size in bytes of the DRAM ECC bank1 config SPL_ZYNQMP_DRAM_BANK2_BASE depends on SPL_ZYNQMP_DRAM_ECC_INIT hex "DRAM Bank2 address" default 0x800000000 help Start address of DRAM ECC bank2 config SPL_ZYNQMP_DRAM_BANK2_LEN depends on SPL_ZYNQMP_DRAM_ECC_INIT hex "DRAM Bank2 size" default 0x0 help Size in bytes of the DRAM ECC bank2. A null size takes no action. config SYS_MALLOC_F_LEN default 0x600 config DEFINE_TCM_OCM_MMAP bool "Define TCM and OCM memory in MMU Table" default y if MP help This option if enabled defines the TCM and OCM memory and its memory attributes in MMU table entry. config ZYNQMP_PSU_INIT_ENABLED bool "Include psu_init" select BOARD_EARLY_INIT_F help Include psu_init to full u-boot. config SPL_ZYNQMP_PSU_INIT_ENABLED bool "Include psu_init in SPL" default y if SPL select BOARD_EARLY_INIT_F help Include psu_init by default in SPL. config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED bool "Overwrite SPL bootmode" depends on SPL help Overwrite bootmode selected via boot mode pins to tell SPL what should be the next boot device. config SPL_ZYNQMP_RESTORE_JTAG bool "Restore JTAG" depends on SPL help Booting SPL in secure mode causes the CSU to disable the JTAG interface even if no eFuses were burnt. This option restores the interface if possible. config ZYNQ_SDHCI_MAX_FREQ default 200000000 config SPL_ZYNQMP_ALT_BOOTMODE hex default 0x0 if JTAG_MODE default 0x1 if QSPI_MODE_24BIT default 0x2 if QSPI_MODE_32BIT default 0x3 if SD_MODE default 0x4 if NAND_MODE default 0x5 if SD_MODE1 default 0x6 if EMMC_MODE default 0x7 if USB_MODE default 0xa if SW_USBHOST_MODE default 0xb if SW_SATA_MODE default 0xe if SD1_LSHFT_MODE choice prompt "Boot mode" depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED default JTAG_MODE config JTAG_MODE bool "JTAG_MODE" config QSPI_MODE_24BIT bool "QSPI_MODE_24BIT" config QSPI_MODE_32BIT bool "QSPI_MODE_32BIT" config SD_MODE bool "SD_MODE" config SD_MODE1 bool "SD_MODE1" config NAND_MODE bool "NAND_MODE" config EMMC_MODE bool "EMMC_MODE" config USB_MODE bool "USB" config SW_USBHOST_MODE bool "SW USBHOST_MODE" config SW_SATA_MODE bool "SW SATA_MODE" config SD1_LSHFT_MODE bool "SD1_LSHFT_MODE" endchoice source "board/xilinx/Kconfig" source "board/xilinx/zynqmp/Kconfig" endif