if AM33XX config AM33XX_CHILISOM bool select SUPPORT_SPL choice prompt "AM33xx board select" config TARGET_AM335X_EVM bool "Support am335x_evm" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select TI_I2C_BOARD_DETECT select SUPPORT_EXTENSION_SCAN imply CMD_DM imply SPL_DM imply SPL_DM_SEQ_ALIAS imply SPL_ENV_SUPPORT imply SPL_FS_EXT4 imply SPL_FS_FAT imply SPL_GPIO imply SPL_I2C imply SPL_LIBCOMMON_SUPPORT imply SPL_LIBDISK_SUPPORT imply SPL_LIBGENERIC_SUPPORT imply SPL_MMC imply SPL_NAND_SUPPORT imply SPL_OF_LIBFDT imply SPL_POWER imply SPL_SEPARATE_BSS imply SPL_SERIAL imply SPL_SYS_MALLOC_SIMPLE imply SPL_WATCHDOG imply SPL_YMODEM_SUPPORT help This option specifies support for the AM335x GP and HS EVM development platforms. The AM335x GP EVM is a standalone test, development, and evaluation module system that enables developers to write software and develop hardware around an AM335x processor subsystem. config TARGET_AM335X_BALTOS bool "Support am335x_baltos" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL imply CMD_DM config TARGET_AM335X_IGEP003X bool "Support am335x_igep003x" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL imply CMD_DM config TARGET_AM335X_SHC bool "Support am335x based shc board from bosch" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL imply CMD_DM imply CMD_SPL config TARGET_AM335X_GUARDIAN bool "Support am335x based guardian board from bosch" select BOARD_LATE_INIT select DM select DM_SERIAL select DM_GPIO select VIDEO select PANEL_HX8238D config TARGET_AM335X_SL50 bool "Support am335x_sl50" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL imply CMD_DM config TARGET_BRXRE1 bool "Support BRXRE1" select BOARD_LATE_INIT config TARGET_BRSMARC1 bool "Support BRSMARC1" select BOARD_LATE_INIT config TARGET_BRPPT1 bool "Support BRPPT1" select BOARD_LATE_INIT config TARGET_CHILIBOARD bool "Grinn chiliBoard" select AM33XX_CHILISOM select BOARD_LATE_INIT select DM select DM_SERIAL imply CMD_DM config TARGET_DRACO bool "Support draco" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_ETAMIN bool "Support etamin" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_PCM051 bool "Support pcm051" select DM select DM_GPIO select DM_SERIAL imply CMD_DM config TARGET_PHYCORE_AM335X_R2 bool "Support phyCORE AM335X R2" select DM select DM_GPIO select DM_SERIAL imply CMD_DM config TARGET_PXM2 bool "Support pxm2" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_RASTABAN bool "Support rastaban" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_RUT bool "Support rut" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_THUBAN bool "Support thuban" select BOARD_LATE_INIT select DM select DM_GPIO select DM_SERIAL select FACTORYSET imply CMD_DM config TARGET_PDU001 bool "Support PDU001" select DM select DM_SERIAL imply SPL_SEPARATE_BSS imply CMD_DM help Support for PDU001 platform developed by EETS GmbH. The PDU001 is a processor and display unit developed around the Computing-Module m2 from bytes at work AG. endchoice config CLOCK_SYNTHESIZER bool "CDCE913 and CDCEL913 clock synthesizer support" help The CDCE913 and CDCEL913 devices are modular PLL-based, low cost, high performance , programmable clock synthesizers. They generate up to 3 output clocks from a single input frequency. Each output can be programmed for any clock-frequency. config CLK_SYNTHESIZER_I2C_ADDR hex "Clock synthesizer i2c bus address" depends on CLOCK_SYNTHESIZER default 0x65 endif if AM43XX choice prompt "AM43xx board select" config TARGET_AM43XX_EVM bool "Support am43xx_evm" select BOARD_LATE_INIT select TI_I2C_BOARD_DETECT imply DM_I2C imply DM_SPI imply DM_SPI_FLASH imply SPL_ENV_SUPPORT imply SPL_FS_EXT4 imply SPL_FS_FAT imply SPL_GPIO imply SPL_I2C imply SPL_LIBCOMMON_SUPPORT imply SPL_LIBDISK_SUPPORT imply SPL_LIBGENERIC_SUPPORT imply SPL_MMC imply SPL_NAND_SUPPORT imply SPL_POWER imply SPL_SERIAL imply SPL_WATCHDOG imply SPL_YMODEM_SUPPORT help This option specifies support for the AM43xx GP and HS EVM development platforms.The AM437x GP EVM is a standalone test, development, and evaluation module system that enables developers to write software and develop hardware around an AM43xx processor subsystem. config TARGET_CM_T43 bool "Support cm_t43" endchoice config SPL_RTC_DDR_SUPPORT bool depends on SPL prompt "Enable RTC-DDR ONLY Support" help If you want RTC-DDR ONLY Support, say Y. RTC Only with DDR in self-refresh mode is a special power saving mode where in all the other voltages are turned off apart from the RTC domain and DDR. So only RTC is alive and ticking and one can program it to wake up after a predetermined period. Once RTC alarm fires, the PMIC powers up all the voltage domains. U-Boot takes a special path as the DDR has contents is in self-refresh and restore path is followed. endif if AM43XX || AM33XX config PUB_ROM_DATA_SIZE hex "Size in bytes of the L3 SRAM reserved by ROM to store data" default 0x8400 help During the device boot, the public ROM uses the top of the public L3 OCMC RAM to store r/w data like stack, heap, globals etc. When the ROM is copying the boot image from the boot media into memory, the image must not spill over into this area. This value can be used during compile time to determine the maximum size of a boot image. Once the ROM transfers control to the boot image, this area is no longer used, and can be reclaimed for run time use by the boot image. endif config AM335X_USB0 bool "Static mode configuration for USB0 in SPL" depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL choice prompt "USB0 port configuration" depends on AM335X_USB0 config AM335X_USB0_HOST bool "Port is used in host mode" config AM335X_USB0_PERIPHERAL bool "Port is used in peripheral mode" endchoice config AM335X_USB1 bool "Static mode configuration for USB1 in SPL" depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL choice prompt "USB1 port configuration" depends on AM335X_USB1 config AM335X_USB1_HOST bool "Port is used in host mode" config AM335X_USB1_PERIPHERAL bool "Port is used in peripheral mode" endchoice