// SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2016-2018, 2020 NXP * Copyright 2014-2015 Freescale Semiconductor, Inc. */ #include #include #include #include #include #include #include #include #include #include #ifdef CONFIG_SYS_FSL_SRDS_1 static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT]; #endif #ifdef CONFIG_SYS_FSL_SRDS_2 static u8 serdes2_prtcl_map[SERDES_PRCTL_COUNT]; #endif #ifdef CONFIG_SYS_NXP_SRDS_3 static u8 serdes3_prtcl_map[SERDES_PRCTL_COUNT]; #endif #if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) #if defined(CONFIG_ARCH_LX2160A) || defined(CONFIG_ARCH_LX2162A) int xfi_dpmac[XFI14 + 1]; int sgmii_dpmac[SGMII18 + 1]; int a25gaui_dpmac[_25GE10 + 1]; int xlaui_dpmac[_40GE2 + 1]; int caui2_dpmac[_50GE2 + 1]; int caui4_dpmac[_100GE2 + 1]; #else int xfi_dpmac[XFI8 + 1]; int sgmii_dpmac[SGMII16 + 1]; #endif #endif __weak void wriop_init_dpmac_qsgmii(int sd, int lane_prtcl) { return; } /* *The return value of this func is the serdes protocol used. *Typically this function is called number of times depending *upon the number of serdes blocks in the Silicon. *Zero is used to denote that no serdes was enabled, *this is the case when golden RCW was used where DPAA2 bring was *intentionally removed to achieve boot to prompt */ __weak int serdes_get_number(int serdes, int cfg) { return cfg; } int is_serdes_configured(enum srds_prtcl device) { int ret = 0; #ifdef CONFIG_SYS_FSL_SRDS_1 if (!serdes1_prtcl_map[NONE]) fsl_serdes_init(); ret |= serdes1_prtcl_map[device]; #endif #ifdef CONFIG_SYS_FSL_SRDS_2 if (!serdes2_prtcl_map[NONE]) fsl_serdes_init(); ret |= serdes2_prtcl_map[device]; #endif #ifdef CONFIG_SYS_NXP_SRDS_3 if (!serdes3_prtcl_map[NONE]) fsl_serdes_init(); ret |= serdes3_prtcl_map[device]; #endif return !!ret; } int serdes_get_first_lane(u32 sd, enum srds_prtcl device) { struct ccsr_gur __iomem *gur = (void *)(CFG_SYS_FSL_GUTS_ADDR); u32 cfg = 0; int i; switch (sd) { #ifdef CONFIG_SYS_FSL_SRDS_1 case FSL_SRDS_1: cfg = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]); cfg &= FSL_CHASSIS3_SRDS1_PRTCL_MASK; cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT; break; #endif #ifdef CONFIG_SYS_FSL_SRDS_2 case FSL_SRDS_2: cfg = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS2_REGSR - 1]); cfg &= FSL_CHASSIS3_SRDS2_PRTCL_MASK; cfg >>= FSL_CHASSIS3_SRDS2_PRTCL_SHIFT; break; #endif #ifdef CONFIG_SYS_NXP_SRDS_3 case NXP_SRDS_3: cfg = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS3_REGSR - 1]); cfg &= FSL_CHASSIS3_SRDS3_PRTCL_MASK; cfg >>= FSL_CHASSIS3_SRDS3_PRTCL_SHIFT; break; #endif default: printf("invalid SerDes%d\n", sd); break; } cfg = serdes_get_number(sd, cfg); /* Is serdes enabled at all? */ if (cfg == 0) return -ENODEV; for (i = 0; i < SRDS_MAX_LANES; i++) { if (serdes_get_prtcl(sd, cfg, i) == device) return i; } return -ENODEV; } void serdes_init(u32 sd, u32 sd_addr, u32 rcwsr, u32 sd_prctl_mask, u32 sd_prctl_shift, u8 serdes_prtcl_map[SERDES_PRCTL_COUNT]) { struct ccsr_gur __iomem *gur = (void *)(CFG_SYS_FSL_GUTS_ADDR); u32 cfg; int lane; if (serdes_prtcl_map[NONE]) return; memset(serdes_prtcl_map, 0, sizeof(u8) * SERDES_PRCTL_COUNT); cfg = gur_in32(&gur->rcwsr[rcwsr - 1]) & sd_prctl_mask; cfg >>= sd_prctl_shift; cfg = serdes_get_number(sd, cfg); if (cfg == 0) { printf("SERDES%d is disabled\n", sd + 1); } else { printf("Using SERDES%d Protocol: %d (0x%x)\n", sd + 1, cfg, cfg); if (!is_serdes_prtcl_valid(sd, cfg)) printf("SERDES%d[PRTCL] = 0x%x is not valid\n", sd + 1, cfg); } for (lane = 0; lane < SRDS_MAX_LANES; lane++) { enum srds_prtcl lane_prtcl = serdes_get_prtcl(sd, cfg, lane); if (unlikely(lane_prtcl >= SERDES_PRCTL_COUNT)) debug("Unknown SerDes lane protocol %d\n", lane_prtcl); else { serdes_prtcl_map[lane_prtcl] = 1; #if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) #if defined(CONFIG_ARCH_LX2160A) || defined(CONFIG_ARCH_LX2162A) if (lane_prtcl >= XFI1 && lane_prtcl <= XFI14) wriop_init_dpmac(sd, xfi_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= SGMII1 && lane_prtcl <= SGMII18) wriop_init_dpmac(sd, sgmii_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= _25GE1 && lane_prtcl <= _25GE10) wriop_init_dpmac(sd, a25gaui_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= _40GE1 && lane_prtcl <= _40GE2) wriop_init_dpmac(sd, xlaui_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= _50GE1 && lane_prtcl <= _50GE2) wriop_init_dpmac(sd, caui2_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= _100GE1 && lane_prtcl <= _100GE2) wriop_init_dpmac(sd, caui4_dpmac[lane_prtcl], (int)lane_prtcl); #else switch (lane_prtcl) { case QSGMII_A: case QSGMII_B: case QSGMII_C: case QSGMII_D: wriop_init_dpmac_qsgmii(sd, (int)lane_prtcl); break; default: if (lane_prtcl >= XFI1 && lane_prtcl <= XFI8) wriop_init_dpmac(sd, xfi_dpmac[lane_prtcl], (int)lane_prtcl); if (lane_prtcl >= SGMII1 && lane_prtcl <= SGMII16) wriop_init_dpmac(sd, sgmii_dpmac[ lane_prtcl], (int)lane_prtcl); break; } #endif #endif } } /* Set the first element to indicate serdes has been initialized */ serdes_prtcl_map[NONE] = 1; } __weak int get_serdes_volt(void) { return -1; } __weak int set_serdes_volt(int svdd) { return -1; } #define LNAGCR0_RT_RSTB 0x00600000 #define RSTCTL_RESET_MASK 0x000000E0 #define RSTCTL_RSTREQ 0x80000000 #define RSTCTL_RST_DONE 0x40000000 #define RSTCTL_RSTERR 0x20000000 #define RSTCTL_SDEN 0x00000020 #define RSTCTL_SDRST_B 0x00000040 #define RSTCTL_PLLRST_B 0x00000080 #define TCALCR_CALRST_B 0x08000000 struct serdes_prctl_info { u32 id; u32 mask; u32 shift; }; struct serdes_prctl_info srds_prctl_info[] = { #ifdef CONFIG_SYS_FSL_SRDS_1 {.id = 1, .mask = FSL_CHASSIS3_SRDS1_PRTCL_MASK, .shift = FSL_CHASSIS3_SRDS1_PRTCL_SHIFT }, #endif #ifdef CONFIG_SYS_FSL_SRDS_2 {.id = 2, .mask = FSL_CHASSIS3_SRDS2_PRTCL_MASK, .shift = FSL_CHASSIS3_SRDS2_PRTCL_SHIFT }, #endif #ifdef CONFIG_SYS_NXP_SRDS_3 {.id = 3, .mask = FSL_CHASSIS3_SRDS3_PRTCL_MASK, .shift = FSL_CHASSIS3_SRDS3_PRTCL_SHIFT }, #endif {} /* NULL ENTRY */ }; static int get_serdes_prctl_info_idx(u32 serdes_id) { int pos = 0; struct serdes_prctl_info *srds_info; /* loop until NULL ENTRY defined by .id=0 */ for (srds_info = srds_prctl_info; srds_info->id != 0; srds_info++, pos++) { if (srds_info->id == serdes_id) return pos; } return -1; } static void do_enabled_lanes_reset(u32 serdes_id, u32 cfg, struct ccsr_serdes __iomem *serdes_base, bool cmplt) { int i, pos; u32 cfg_tmp; pos = get_serdes_prctl_info_idx(serdes_id); if (pos == -1) { printf("invalid serdes_id %d\n", serdes_id); return; } cfg_tmp = cfg & srds_prctl_info[pos].mask; cfg_tmp >>= srds_prctl_info[pos].shift; for (i = 0; i < 4 && cfg_tmp & (0xf << (3 - i)); i++) { if (cmplt) setbits_le32(&serdes_base->lane[i].gcr0, LNAGCR0_RT_RSTB); else clrbits_le32(&serdes_base->lane[i].gcr0, LNAGCR0_RT_RSTB); } } static void do_pll_reset(u32 cfg, struct ccsr_serdes __iomem *serdes_base) { int i; for (i = 0; i < 2 && !(cfg & (0x1 << (1 - i))); i++) { clrbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_RESET_MASK); udelay(1); setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_RSTREQ); } udelay(1); } static void do_rx_tx_cal_reset(struct ccsr_serdes __iomem *serdes_base) { clrbits_le32(&serdes_base->srdstcalcr, TCALCR_CALRST_B); clrbits_le32(&serdes_base->srdstcalcr, TCALCR_CALRST_B); } static void do_rx_tx_cal_reset_comp(u32 cfg, int i, struct ccsr_serdes __iomem *serdes_base) { if (!(cfg == 0x3 && i == 1)) { udelay(1); setbits_le32(&serdes_base->srdstcalcr, TCALCR_CALRST_B); setbits_le32(&serdes_base->srdstcalcr, TCALCR_CALRST_B); } udelay(1); } static void do_pll_reset_done(u32 cfg, struct ccsr_serdes __iomem *serdes_base) { int i; u32 reg = 0; for (i = 0; i < 2; i++) { reg = in_le32(&serdes_base->bank[i].pllcr0); if (!(cfg & (0x1 << (1 - i))) && ((reg >> 23) & 0x1)) { setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_RST_DONE); } } } static void do_serdes_enable(u32 cfg, struct ccsr_serdes __iomem *serdes_base) { int i; for (i = 0; i < 2 && !(cfg & (0x1 << (1 - i))); i++) { setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_SDEN); udelay(1); setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_PLLRST_B); udelay(1); /* Take the Rx/Tx calibration out of reset */ do_rx_tx_cal_reset_comp(cfg, i, serdes_base); } } static void do_pll_lock(u32 cfg, struct ccsr_serdes __iomem *serdes_base) { int i; u32 reg = 0; for (i = 0; i < 2 && !(cfg & (0x1 << (1 - i))); i++) { /* if the PLL is not locked, set RST_ERR */ reg = in_le32(&serdes_base->bank[i].pllcr0); if (!((reg >> 23) & 0x1)) { setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_RSTERR); } else { udelay(1); setbits_le32(&serdes_base->bank[i].rstctl, RSTCTL_SDRST_B); udelay(1); } } } int setup_serdes_volt(u32 svdd) { struct ccsr_gur __iomem *gur = (void *)(CFG_SYS_FSL_GUTS_ADDR); struct ccsr_serdes __iomem *serdes1_base = (void *)CFG_SYS_FSL_LSCH3_SERDES_ADDR; u32 cfg_rcwsrds1 = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]); #ifdef CONFIG_SYS_FSL_SRDS_2 struct ccsr_serdes __iomem *serdes2_base = (void *)(CFG_SYS_FSL_LSCH3_SERDES_ADDR + 0x10000); u32 cfg_rcwsrds2 = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS2_REGSR - 1]); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 struct ccsr_serdes __iomem *serdes3_base = (void *)(CFG_SYS_FSL_LSCH3_SERDES_ADDR + 0x20000); u32 cfg_rcwsrds3 = gur_in32(&gur->rcwsr[FSL_CHASSIS3_SRDS3_REGSR - 1]); #endif u32 cfg_tmp; int svdd_cur, svdd_tar; int ret = 1; /* Only support switch SVDD to 900mV */ if (svdd != 900) return -EINVAL; /* Scale up to the LTC resolution is 1/4096V */ svdd = (svdd * 4096) / 1000; svdd_tar = svdd; svdd_cur = get_serdes_volt(); if (svdd_cur < 0) return -EINVAL; debug("%s: current SVDD: %x; target SVDD: %x\n", __func__, svdd_cur, svdd_tar); if (svdd_cur == svdd_tar) return 0; /* Put the all enabled lanes in reset */ #ifdef CONFIG_SYS_FSL_SRDS_1 do_enabled_lanes_reset(1, cfg_rcwsrds1, serdes1_base, false); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 do_enabled_lanes_reset(2, cfg_rcwsrds2, serdes2_base, false); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 do_enabled_lanes_reset(3, cfg_rcwsrds3, serdes3_base, false); #endif /* Put the all enabled PLL in reset */ #ifdef CONFIG_SYS_FSL_SRDS_1 cfg_tmp = cfg_rcwsrds1 & 0x3; do_pll_reset(cfg_tmp, serdes1_base); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 cfg_tmp = cfg_rcwsrds1 & 0xC; cfg_tmp >>= 2; do_pll_reset(cfg_tmp, serdes2_base); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 cfg_tmp = cfg_rcwsrds3 & 0x30; cfg_tmp >>= 4; do_pll_reset(cfg_tmp, serdes3_base); #endif /* Put the Rx/Tx calibration into reset */ #ifdef CONFIG_SYS_FSL_SRDS_1 do_rx_tx_cal_reset(serdes1_base); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 do_rx_tx_cal_reset(serdes2_base); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 do_rx_tx_cal_reset(serdes3_base); #endif ret = set_serdes_volt(svdd); if (ret < 0) { printf("could not change SVDD\n"); ret = -1; } /* For each PLL that’s not disabled via RCW enable the SERDES */ #ifdef CONFIG_SYS_FSL_SRDS_1 cfg_tmp = cfg_rcwsrds1 & 0x3; do_serdes_enable(cfg_tmp, serdes1_base); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 cfg_tmp = cfg_rcwsrds1 & 0xC; cfg_tmp >>= 2; do_serdes_enable(cfg_tmp, serdes2_base); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 cfg_tmp = cfg_rcwsrds3 & 0x30; cfg_tmp >>= 4; do_serdes_enable(cfg_tmp, serdes3_base); #endif /* Wait for at at least 625us, ensure the PLLs being reset are locked */ udelay(800); #ifdef CONFIG_SYS_FSL_SRDS_1 cfg_tmp = cfg_rcwsrds1 & 0x3; do_pll_lock(cfg_tmp, serdes1_base); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 cfg_tmp = cfg_rcwsrds1 & 0xC; cfg_tmp >>= 2; do_pll_lock(cfg_tmp, serdes2_base); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 cfg_tmp = cfg_rcwsrds3 & 0x30; cfg_tmp >>= 4; do_pll_lock(cfg_tmp, serdes3_base); #endif /* Take the all enabled lanes out of reset */ #ifdef CONFIG_SYS_FSL_SRDS_1 do_enabled_lanes_reset(1, cfg_rcwsrds1, serdes1_base, true); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 do_enabled_lanes_reset(2, cfg_rcwsrds2, serdes2_base, true); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 do_enabled_lanes_reset(3, cfg_rcwsrds3, serdes3_base, true); #endif /* For each PLL being reset, and achieved PLL lock set RST_DONE */ #ifdef CONFIG_SYS_FSL_SRDS_1 cfg_tmp = cfg_rcwsrds1 & 0x3; do_pll_reset_done(cfg_tmp, serdes1_base); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 cfg_tmp = cfg_rcwsrds1 & 0xC; cfg_tmp >>= 2; do_pll_reset_done(cfg_tmp, serdes2_base); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 cfg_tmp = cfg_rcwsrds3 & 0x30; cfg_tmp >>= 4; do_pll_reset_done(cfg_tmp, serdes3_base); #endif return ret; } void fsl_serdes_init(void) { #if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) int i , j; #if defined(CONFIG_ARCH_LX2160A) || defined(CONFIG_ARCH_LX2162A) for (i = XFI1, j = 1; i <= XFI14; i++, j++) xfi_dpmac[i] = j; for (i = SGMII1, j = 1; i <= SGMII18; i++, j++) sgmii_dpmac[i] = j; for (i = _25GE1, j = 1; i <= _25GE10; i++, j++) a25gaui_dpmac[i] = j; for (i = _40GE1, j = 1; i <= _40GE2; i++, j++) xlaui_dpmac[i] = j; for (i = _50GE1, j = 1; i <= _50GE2; i++, j++) caui2_dpmac[i] = j; for (i = _100GE1, j = 1; i <= _100GE2; i++, j++) caui4_dpmac[i] = j; #else for (i = XFI1, j = 1; i <= XFI8; i++, j++) xfi_dpmac[i] = j; for (i = SGMII1, j = 1; i <= SGMII16; i++, j++) sgmii_dpmac[i] = j; #endif #endif #ifdef CONFIG_SYS_FSL_SRDS_1 serdes_init(FSL_SRDS_1, CFG_SYS_FSL_LSCH3_SERDES_ADDR, FSL_CHASSIS3_SRDS1_REGSR, FSL_CHASSIS3_SRDS1_PRTCL_MASK, FSL_CHASSIS3_SRDS1_PRTCL_SHIFT, serdes1_prtcl_map); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 serdes_init(FSL_SRDS_2, CFG_SYS_FSL_LSCH3_SERDES_ADDR + FSL_SRDS_2 * 0x10000, FSL_CHASSIS3_SRDS2_REGSR, FSL_CHASSIS3_SRDS2_PRTCL_MASK, FSL_CHASSIS3_SRDS2_PRTCL_SHIFT, serdes2_prtcl_map); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 serdes_init(NXP_SRDS_3, CFG_SYS_FSL_LSCH3_SERDES_ADDR + NXP_SRDS_3 * 0x10000, FSL_CHASSIS3_SRDS3_REGSR, FSL_CHASSIS3_SRDS3_PRTCL_MASK, FSL_CHASSIS3_SRDS3_PRTCL_SHIFT, serdes3_prtcl_map); #endif } int serdes_set_env(int sd, int rcwsr, int sd_prctl_mask, int sd_prctl_shift) { struct ccsr_gur __iomem *gur = (void *)(CFG_SYS_FSL_GUTS_ADDR); char scfg[16], snum[16]; int cfgr = 0; u32 cfg; cfg = gur_in32(&gur->rcwsr[rcwsr - 1]) & sd_prctl_mask; cfg >>= sd_prctl_shift; cfg = serdes_get_number(sd, cfg); #if defined(SRDS_BITS_PER_LANE) /* * reverse lanes, lane 0 should be printed first so it must be moved to * high order bits. * For example bb58 should read 85bb, lane 0 being protocol 8. * This only applies to SoCs that define SRDS_BITS_PER_LANE and have * independent per-lane protocol configuration, at this time LS1028A and * LS1088A. LS2 and LX2 SoCs encode the full protocol mix across all * lanes as a single value. */ for (int i = 0; i < SRDS_MAX_LANES; i++) { int tmp; tmp = cfg >> (i * SRDS_BITS_PER_LANE); tmp &= GENMASK(SRDS_BITS_PER_LANE - 1, 0); tmp <<= (SRDS_MAX_LANES - i - 1) * SRDS_BITS_PER_LANE; cfgr |= tmp; } #endif /* SRDS_BITS_PER_LANE */ snprintf(snum, 16, "serdes%d", sd); snprintf(scfg, 16, "%x", cfgr); env_set(snum, scfg); return 0; } int serdes_misc_init(void) { #ifdef CONFIG_SYS_FSL_SRDS_1 serdes_set_env(FSL_SRDS_1, FSL_CHASSIS3_SRDS1_REGSR, FSL_CHASSIS3_SRDS1_PRTCL_MASK, FSL_CHASSIS3_SRDS1_PRTCL_SHIFT); #endif #ifdef CONFIG_SYS_FSL_SRDS_2 serdes_set_env(FSL_SRDS_2, FSL_CHASSIS3_SRDS2_REGSR, FSL_CHASSIS3_SRDS2_PRTCL_MASK, FSL_CHASSIS3_SRDS2_PRTCL_SHIFT); #endif #ifdef CONFIG_SYS_NXP_SRDS_3 serdes_set_env(NXP_SRDS_3, FSL_CHASSIS3_SRDS3_REGSR, FSL_CHASSIS3_SRDS3_PRTCL_MASK, FSL_CHASSIS3_SRDS3_PRTCL_SHIFT); #endif return 0; }